|
|
Mercedes of the S-class W2021993-2000 of releaseRepair and operation of the car |
|
|
Mercedes W202 + 1.2. General information + 2. Maintenance - 3. Engines 3.1.2. Identification number + 3.1.3. Engine 3.1.4. Cars with the conditioner 3.1.5. Lower cover of a motor compartment 3.1.6. Covers of cast openings 3.1.7. Natyazhitel of a chain + 3.1.8. Cover of a head of the block of cylinders + 3.1.9. Head of the block of cylinders + 3.1.10. Camshafts 3.1.11. Hydraulic dish-shaped pushers 3.1.12. Maslootrazhatelny caps 3.1.13. Valves 3.1.14. The directing valves 3.1.15. Saddles of valves in a head of the block of cylinders 3.1.16. Compression + 3.1.17. Maple belt 3.1.18. Diagnostics of malfunctions (DB) 3.1.19. General comments 3.1.20. Repair work without dismantle of the engine - 3.1.21. Capital repairs of the engine 3.1.21.2. Alternatives 3.1.21.3. Dismantle of the engine 3.1.21.4. Sequence of dismantling + 3.2. Diesel Engine (DE) 3.2.3. Cars with the conditioner 3.2.4. Lower cover of a motor compartment 3.2.5. Covers of cast openings 3.2.6. Natyazhitel of a chain + 3.2.7. Camshaft + 3.2.8. Head of the block of cylinders + 3.2.9. Maslootrazhatelny caps 3.2.10. Cover of a head of the block of cylinders (2,2 / 2,5 l) 3.2.11. Hydraulic dish-shaped pushers 3.2.12. Valves 3.2.13. The directing valves 3.2.14. Saddles of valves in a head of the block of cylinders 3.2.15. Head of the block of cylinders and motor block 3.2.16. Compression 3.2.17. Maple ridge belt 3.2.18. The pulling device of a maple ridge belt 3.2.19. Diagnostics of malfunctions (DD) + 4. Lubrication system + 5. Cooling system + 6. Heating, ventilation + 7. System of ignition + 8. Fuel system + 9. Transmission + 10. Running gear + 11. Steering + 12. Brake system + 13. Body + 14. Electric equipment + 14.2. Electrical circuitries |
3.1.21.4. Sequence of dismantling
The easiest to disassemble the engine and to make all types of works at the figurative stand. Before installation of the engine it is necessary to shoot a flywheel with the coupling mechanism with the stand. If there is no stand, then it is possible to disassemble the engine having strengthened it on a strong workbench or on a floor. When dismantling without stand be very careful during manipulations with the engine. If the engine is taken to repare, then at first it is necessary to remove all units to install them subsequently just in the same order as well as at independent capital repairs. Treat such units: – generator and arms; Prevention If the block of cylinders of an incomplete complete set, i.e. the block of cylinders with installed by the krivoshipno-conrod mechanism and piston group is installed, then it is also necessary to remove a block head, the oil pallet and the oil pump. The list of the details which are subject to removal is defined by the accepted repair option. If it is planned to make complete capital repairs, then the engine it is necessary to sort and remove completely engine details in the following order: – covers of a gear belt of a cam-shaft; Before dismantling and performing procedures of capital repairs the following tools and the equipment will be necessary: – standard set of the tool; |
|