Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car

Mercedes W202
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Lower cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic dish-shaped pushers
   3.1.12. Maslootrazhatelny caps
   3.1.13. Valves
   3.1.14. The directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   + 3.1.17. Maple belt
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without dismantle of the engine
   + 3.1.21. Capital repairs of the engine
   + 3.2. Diesel Engine (DE)
   3.2.3. Cars with the conditioner
   3.2.4. Lower cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelny caps
   3.2.10. Cover of a head of the block of cylinders (2,2 / 2,5 l)
   3.2.11. Hydraulic dish-shaped pushers
   3.2.12. Valves
   3.2.13. The directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. The pulling device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries

3.2.18. The pulling device of a maple ridge belt

Removal

PERFORMANCE ORDER

	1. Remove the hydraulic coupling of the fan.
Prevention The cap nut has the left carving.
2. Remove a fan casing.
3. Take off maple a ridge belt.
4. Wring out the screw-driver a locking cover of a tension roller.
5. Unscrew a tension roller.
6. 2,0 l engine: unscrew a belt pulley of the pump of cooling liquid.
7. Unscrew the belt tension device shock-absorber.
8. Unhook a stretching spring.
9. Unscrew a conical bolt from the spring tension lever, previously having wrung out a locking cover.
10. Remove the spring tension lever, track at the same time safety of a sealing ring and pro-masonry washer.

Installation

PERFORMANCE ORDER

1. Install the spring tension lever with a sealing ring and a pro-masonry washer and tighten with the moment 100 N. of m.

Prevention

Clear a carving a wire brush before installation and cover with sealant (the carving needs to be degreased).

2. Insert a locking cover.

3. Hang a stretching spring.

4. Twirl the shock-absorber of the pulling device above with m 25 N.' moment, and below with m 20 N.' moment.

Prevention

If you install the new shock-absorber, then previously surely remove air from it. For this purpose in the provision of installation several times move a piston rod backwards-forward.

5. 2,0 l engine: twirl a belt pulley of the pump of cooling liquid with m 10 N.' moment (a bolt with an internal hexagon) or 15 N. of m (the torsion bolt).

6. Screw a tension roller with m 25 N.' moment (the engine of 2,0 l) or 30 N. of m (the l engine 2,2 / 2,5). Insert a locking cover.

7. Establish maple a ridge belt.

8. Establish a fan casing.

9. Install the hydraulic coupling of the fan.