| 1. Check engine support, hoses of cooling liquid, fuel-supply lines and oil pipelines for porosity and existence of cracks, in case of need replace them. |
| 2. Check the radial ball-bearing of the crankshaft and the persistent bearing of coupling on ease of rotation, and the coupling bearing on easily mobility. |
| 3. Check whether thickness and what condition of overlays of a frictional clutch plate is sufficient. |
| 4. If separated, attach the transmission to the engine and enter them together into a motor compartment. |
| 5. At installation the engine should be lowered carefully not to damage the leading shaft, coupling and a body. |
| 6. Twirl the bolts connecting the engine and the transmission. |
| 7. Twirl bolts of fastening of forward bearings manually. |
| 8. Tighten bolts of fastening of a back arm of the engine with m 45 N.' moment, and nuts – with m 70 N.' moment * |
| 9. Screw up bolts of forward bearings of engines with m 30 N.' moment. |
| 10. Remove a jack and disconnect a cable from the engine. |
| 11. Install the driveshaft in the transmission. * |
| 12. Screw the convector on average the tunnel. * |
| 13. Screw a side support of the gas device on the check point. * |
| 14. If the engine was removed without transmission, establish a starter. |
| 15. Screw a wire of "weight" between a starter and a body. |
| 16. Connect electric wires to a starter. |
| 17. Screw the sensor of the speed (L3).* |
| 18. Screw the tachometric inductive sensor if it is. |
| 19. Automatic transmission: connect the lever mechanism of switching to the check point and insert an element of connection of wires of switches of blocking of start and tail light (S 16/1). Establish an element of connection of wires of the magnetic Kickdown valve on the right side of the transmission. Check adjustment of the mechanism of switching. * |
| 20. Screw a hydraulic hose of the sensor of coupling, remove air from the coupling sensor. * |
| 21. Mechanical transmission: install rods of forks on handles of switching of the transmission and record clips. Check adjustment. |
| 22. Automatic transmission: screw oil pipelines of the air oil cooler. |
| 23. Remove clips for hoses. |
| 24. Adjustment of level: screw oil pipelines / masloshlang on the delivery oil pump. |
| 25. Fasten hydraulic hoses of a servonasos with m 30 N.' moment. |
| 26. Connect all electric wires, that is, glow plugs, the thermoswitch plug, a wire of the generator of three-phase current, the sensor of level of oil and the switch of pressure of oil. |
| 27. Strengthen a phase wire in the holder over a starter. |
| 28. Conditioner: fasten with the moment 25 N. of m the refrigerating compressor. Establish ridge maple a belt. |
| 29. Establish a radiator. |
| 30. Put on all hoses of cooling liquid and fix communications. |
| 31. Check availability of antifreeze in cooling liquid and fill in. |
| 32. Screw a final collector on a flange of withdrawal of an exhaust pipe. |
| 33. Connect a positive cable (X4) to the subconnecting element located at the left in the bottom of the car. |
| 34. Establish the lower cover of a motor compartment. |
| 35. Lower the car. |
| 36. Establish a cable of management of gas and adjust it. |
| 37. Insert draft into an engine cowl. |
| 38. Screw a forward cross basic beam with a strut. |
| 39. Insert fuel-supply lines according to the marking applied on them. |
| 40. Screw a depression hose for the amplifier of braking on the vacuum pump. |
| 41. Put on all hoses of depression which conduct to the engine. |
| 42. Check oil level in a box, in case of need add it. |
| 43. Fill in hydraulic oil for the amplifier of steering, remove air from the amplifier. |
| 44. Clean the air filter, if necessary replace it. |
| 45. Install the air filter. |
| 46. Establish an air hose. |
| 47. Connect a wire of "weight" to the battery. |
| 48. Bring the engine to working temperature, check the level of brake fluid and check tightness of all elements of connection of hoses. |
| 49. To close an engine cowl, pull the lock lever at the left hinge and slowly lower a cowl until the lever is fixed. |