Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car


Mercedes W202
+ 1.2. General information
+ 2. Maintenance
- 3. Engines
   3.1.2. Identification number
   + 3.1.3. Engine
   3.1.4. Cars with the conditioner
   3.1.5. Lower cover of a motor compartment
   3.1.6. Covers of cast openings
   3.1.7. Natyazhitel of a chain
   + 3.1.8. Cover of a head of the block of cylinders
   + 3.1.9. Head of the block of cylinders
   + 3.1.10. Camshafts
   3.1.11. Hydraulic dish-shaped pushers
   3.1.12. Maslootrazhatelny caps
   3.1.13. Valves
   3.1.14. The directing valves
   3.1.15. Saddles of valves in a head of the block of cylinders
   3.1.16. Compression
   - 3.1.17. Maple belt
      3.1.17.2. 6-cylinder engine
   3.1.18. Diagnostics of malfunctions (DB)
   3.1.19. General comments
   3.1.20. Repair work without dismantle of the engine
   + 3.1.21. Capital repairs of the engine
   + 3.2. Diesel Engine (DE)
   3.2.3. Cars with the conditioner
   3.2.4. Lower cover of a motor compartment
   3.2.5. Covers of cast openings
   3.2.6. Natyazhitel of a chain
   + 3.2.7. Camshaft
   + 3.2.8. Head of the block of cylinders
   + 3.2.9. Maslootrazhatelny caps
   3.2.10. Cover of a head of the block of cylinders (2,2 / 2,5 l)
   3.2.11. Hydraulic dish-shaped pushers
   3.2.12. Valves
   3.2.13. The directing valves
   3.2.14. Saddles of valves in a head of the block of cylinders
   3.2.15. Head of the block of cylinders and motor block
   3.2.16. Compression
   3.2.17. Maple ridge belt
   3.2.18. The pulling device of a maple ridge belt
   3.2.19. Diagnostics of malfunctions (DD)
+ 4. Lubrication system
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries




3.1.17.2. 6-cylinder engine

 Removal
PERFORMANCE ORDER
1. Extend the fixing uvula (1) from a ring of a casing of the fan (2). Turn a covering in the direction of the beaten-out arrow "open" and remove, turning a krylchatka of the fan.
2. Weaken a bolt (16) on 1/4–1/2 turns. Turn a nut (5) to the left, thereby weaken a belt and take off it. In addition represented details: 13 – the index of adjustment, the shooter – the second division.

Installation
 1. The pulling roller
2. Belt pulley of a bent shaft
3. The cooling compressor (conditioner)
5. Fan
7. Air pump
8. Generator
9. The directing roller
10. Pump of the amplifier of steering
11. Pump of cooling liquid
Length: 2337 mm or 2440 mm (with the conditioner)

PERFORMANCE ORDER
1. Check a profile of belt pulleys and the pulling device for absence of damage and pollution, in case of need clean or replace. At the same time pay attention to the beaten-out places of a support of the pulling device and a hole on belt pulleys.
2. Replace maple ridge belts with deposits of dirt between the edges weakened by edges, cracks, a fringe and broken by ribs surely.
3. Impose maple a belt, since the pulling roller, according to the sequence of numbering in the drawing.
4. Establish the index of adjustment on marking (1).
5. Turn a tension nut (5) to the right until the index of adjustment (13) coincides with marking (2).
6. Tighten a bolt (16) with m 75 N.' moment.
7. Visually check landing of a belt on belt pulleys.
8. Establish a fan casing ring, turn and record.





По материалам сайта http://ligazp.org