Mercedes of the S-class W202

1993-2000 of release

Repair and operation of the car



Mercedes W202
+ 1.2. General information
+ 2. Maintenance
+ 3. Engines
- 4. Lubrication system
   4.2. Specification of engine oil
   4.3. Scope viscosity oils / class
   4.4. Oil consumption
   4.5. Contour of circulation of oil (DD)
   4.6. Oil reducing valve
   - 4.7. Oil pallet
      4.7.2. Diesel engine (2,0 l)
      4.7.3. Diesel engine (2,2 / 2,5 l)
   4.8. Oil level indicator
   4.9. The heat exchanger oil - / cooling liquid
   4.10. Diagnostics of malfunctions in an oil circulation contour
+ 5. Cooling system
+ 6. Heating, ventilation
+ 7. System of ignition
+ 8. Fuel system
+ 9. Transmission
+ 10. Running gear
+ 11. Steering
+ 12. Brake system
+ 13. Body
+ 14. Electric equipment
+ 14.2. Electrical circuitries




4.7.2. Diesel engine (2,0 l)

GENERAL INFORMATION

2,0 l diesel engine

 
3. Stopper of a masloslivny opening
6. Engine emphasis (type 201)
24. Engine shock-absorber (type 201)

Removal

PERFORMANCE ORDER
1. Remove the lower cover of a motor compartment.
2. Remove the stabilizer of cross stability.
3. Disconnect the left longitudinal steering draft and the right shock-absorber of steering.
4. Merge engine oil.
5. Disconnect a cable of mass of the battery (–).
Prevention

At the same time the anticreeping code of radio is erased.


6. Disconnect a positive wire of X4 from the place of connection to the lower party of the car at the left and you plozhit from above the engine.
7. Disconnect a casing of the fan and put from above the fan.
8. Unscrew the sensor of the speed (L3).
9. Disconnect a weight wire between a starter and a body (shooter).
10. Remove a shchtekker of the sensor of level of oil.
11. Sort an intermediate steering bipod.
12. Automatic transmission: Separate oil pipelines in connecting details from masloshlang, previously having clamped oil pipelines by means of hose clips. Close elements of connection small plastic bags that dirt did not get into them.
13. Pick up the engine the corresponding cable or a chain for a forward eye (shooter) and raise the crane. If is not present at the disposal of the crane, insert into a cable suitable a shta of NSU, slightly raise the engine and an oboprita on supports.
14. Unscrew from below from a longeron a bolt with an internal hexagon for the left forward support of the engine.
15. Unscrew from a longeron from below a bolt with an internal hexagon of the right forward support of the engine.
16. Raise the engine, it is how possible above.
17. The oil pallet with a priflantsovanny side part: turn off a side part and remove together with sealing laying.
18. Unscrew bolts of fastening (19) of the oil pallet and remove the oil pallet (45) forward, depending on the direction of the movement. If necessary slightly turn a bent shaft.
19. Remove sealing laying (45a), carefully clear the sealing surfaces of the pallet and a case of a bent shaft.

Installation

PERFORMANCE ORDER
1. Negative wire of the rechargeable battery. Install the oil pallet with new sealing laying, having oriented its prileganiye to the back surface of the transmission, and evenly manually twirl fastening bolts. Then alternately screw up bolts with the next moments:
M 6 – 10 N.' m; M 8 – 25 N.' M; M 10 – 40 N.' M.
Prevention

In cars with the automatic transmission track that the calibrated groove on an interface of the oil pallet entered the unloading plug of the motor block.

2. If there was a removal: establish a side part of the oil pallet with new sealing laying and twirl with the moment 10 N. of m.
3. Lower the engine.
4. Establish bolts of fastening of a forward support of the engine and tighten with the moment 30 N. of m.
5. Automatic transmission: connect oil pipelines, remove hose clips.
6. Establish an intermediate steering bipod.
7. Put on the oil level sensor plug.
8. Screw the speed sensor.
9. Screw the weights cable between a starter and a body.
10. Establish and fix by clips a fan casing.
11. Connect a positive cable (X4).
12. Hang the left longitudinal steering draft and the right shock-absorber of steering.
13. Install the stabilizer.
14. Establish the lower cover of a motor compartment.
15. Fill in engine oil.
16. Connect a wire of "mass" of the battery.
17. Expose hours
18. Set an anticreeping code of radio.
19. Warm up the engine and check tightness of the oil pallet.
20. Automatic transmission: check oil level.